www.AMARAD.org mise à jour août 2012
Association des Marins Radios
TECHNIQUE
V
Antennes
[
mailto:amarad@free.fr]
[
./amaradpag.html]
*The Hertz antenna has been around since about 1880 and there are an unlimited number of variations on that theme. However, each of those is constrained to be a resonant antenna. The wires may be straight or bent into various shapes, but they must be resonant or resonated with an antenna tuner. Resonance is necessary to allow maximum current flow. Hertz antennas are based on the concept that current flow on a wire causes the development of a magnetic (H) field, and a changing magnetic field creates an electric (E) field. Because one field creates the other, they have a time phase difference of 90 degrees. The speed at which the two fields travel is different. Therefore, the two become in time phase at a nominal distance of about 1/3 wavelength from the wire. This is called the far field. When they have the proper phase, amplitude, and physical and physical relationship radiation is created.
Compare that to the EH Antenna where the E and H fields are in time phase at the antenna. Because the two fields are very efficiently integrated, the radiation resistance is higher than a wire antenna. A major factor is that the elements of a EH Antenna have a much larger diameter than a wire, and the two elements therefore have high capacity between the elements. This large capacity and high radiation resistance combine to provide very wide bandwidth and high efficiency. All of this in an antenna that may be less than 1% of a wavelength, compared to wire antennas that are 50% of a wavelength.
Keep in mind that the cylinder length to diameter ratio sets the antenna radiation pattern. We typically use a ratio of 6 for all Ham bands above 40 Meters and a ratio of 12 for 40 meters and below. When the antenna is mounted as a vertical, the larger ratio allows high angle radiation. The bandwidth of the antenna is determined by the diameter.
You will find information to allow you to copy antennas for various Ham bands, as well as technical information that will allow you to roll your own. We hope you enjoy this information and the use of the antennas you build. There are an untold number already on the air and many more added every day. If you choose to buy rather than build, check the links for companies that manufacture and sell EH Antennas, then check their distributors.
Ted W5QJR
We now have two AM broadcast antennas, a large one for the low end of the band and a small one for the high end of the band. These are detailed in a speech given to the National Association of Broadcasters in April 2004 and is contained in this section (Power Point presentation). From a historical perspective, the large antenna was developed based on test results from smaller antennas. It has been tested in accordance with FCC field test requirements and has proven to be successful. Recently, we were finally able to develop a computer program to define all of the EH Antenna characteristics, including bandwidth and efficiency, except the radiation pattern. That program was used to develop the new small antenna. This antenna was specifically designed for those radio stations in the new segment of the band above 1600 KHz, but is applicable down to 1200 KHz. The cylinder length to diameter ratio sets the antenna pattern, while the diameter sets the bandwidth. Both the large and small antennas have a length to diameter ratio of 6.
Here are the parameters of the “small” AM Broadcast antenna:
1. Each cylinder is 8 inches in diameter and 48 inches in length.
2. At 1600 KHz the performance parameters are:
· Radiation resistance – 77 ohms
· 3 dB bandwidth- 99 KHz
· Efficiency – 98%
If this antenna is mounted at a height of 1/8 wavelengths it will outperform a “standard” ¼ wavelength vertical. It is so small it lends itself to mounting on top an unguyed tower
[
http://www.eh-antenna.com/index.htm]
[
http://www.eh-antenna.com/library/PPT%20for%20Hams.ppt]
[
http://www.eh-antenna.com/library/AN%20INTRODUCTION%20TO%20EH%20ANTENNAS.pdf]
The AX-05E Long Wire HF Receiver Antenna
is a low-cost kit containing all the necessary components for a simple but effective fast-deployment shortwave antenna suitable for a wide range of short wave, medium wave and long wave listening applications.
This antenna kit consists of approx 25 meters (approx 80 ft) of insulated copper wire, 10 meters (approx 30 ft) of weather-proof rope and two "egg" shaped insulators.
Technical Specifications
Frequency range 0.1 to 30 MHz (approx.)
Impedance 450 ohm typ.
Length Approx. 20 m (approx. 65 ft) when assembled
ANTENNE RECEPTION FOUET MARINE BCL 1-KA 10 KHz à 108 MHz
Cette antenne de réception comprend un fouet de haute capacité combiné avec un amplificateur incorporé dans l'embase de l'antenne.L'amplificateur, construit avec une combinaison de transistors à effet de champ et bipolaires, crée une impédanceexcellente entre le fouet de haute impédance et la câble coaxial 50 ohms sur une bande très large.
L'amplificateur est fourni avec puissance DC à travers le câble 50 ohms à l'aide du boitier de jonction qui peut être installé près du récepteur. Le boitier de jonction sépare les signaux DC et RF et peut avec succès être alimenté de la même source 12v DC que la station RX.La sensibilité de l'amplificateur est optimisée pour que le bruit de l'antenne et du récepteur soit toujours inférieur au bruit capté par l'antenne. L'amplificateur est protégé contre les surcharges RF à l'aide de diodes opposés ; et la large bande dynamique assure des capacités de cross et d'intermodulation excellentes.Le boitier de jonction est protégé contre les inversions accidentelles de polarité et il est filtré pour éviter des interférences.L'antenne peut supporter des conditions météorologiques difficiles et elle est parfaite pour une utilisation marine.
Alimentation : 9-14 V DC
Connecteur : UHF (PL-259)
Longueur Totale : Environ 1,01 m
Poids : Environ 1,0 kg
Fixation : Sur mât 30-45 mm de dia. ou sur surface plate.
DUMMY LOAD
Freqency range 0-2 GHz
Max. input power 100 Watts
Impendance 50 Ohms
SWR < 1.25
Temp. range -30°c / + 60°c
Connectors N-fem.
Dimensions 70 x 70 x 180mm
Weight Approx 1460gr
Freqency range 0-1 (2) GHz
Max. input power 15 Watts
Max. input power extra cooling 30 Watts
Impendance 50 Ohms
SWR < 1.15
Temp. range -30°c / + 60°c
Connectors N-male
Dimensions 40 x 40mm
Weight Approx 105 gr
[
./theorie_2pag.html]
[
./theoriespag.html]
[
http://www.ropeantenna.com/]
[
http://www.ropeantenna.com/]
[
http://www.ropeantenna.com/]
L’ANTENNE CORDE
Le probléme majeur rencontré à bord de tous les voiliers petits ou grand est : “ Comment puis-je installer une antenne d’émission et de réception HF au milieu de toutes les drisses, haubans et cordages de toutes sortes à bord ?“ et la question subsidiaire : “ Lorsque je viens de démâter comment istaller une antenne de secours rapidement accéssible et rapidement gréable ?”
La réponse est l’antenne corde; comme vous pouvez le voir sur les images ci-dessous elle est facilement montable et repérable lorsqu’elle est à poste.
Cliquez ci-dessous sur les images pour en savoir plus sur cette antenne ....
Antenne large bande HF (type W3HH)
Emission / Réception
( Ce n’est pas une nouveauté mais c’est une valeur sure pour une station radio hf )
L'antenne W3HH (c'est l'indicatif de son auteur) est un dipôle replié fermé sur une charge. Elle est aussi connue sous le nom de T2FD, qui signifie en gros Terminated Folded Dipole. Sa longueur totale est l / 3 (le tiers de la longueur d'onde) . On établit cette longueur à partir de la fréquence la plus basse à transmettre. L'antenne est tendue en oblique en faisant un angle de 20 à 40 degrés avec l'horizontale.
L'antenne est pratiquement omnidirectionnelle. Mais si elle est placée en position horizontale, elle présente des lobes marqués. Elle s'alimente normalement en symétrique, mais s'accommode parfaitement d'une alimentation par câble coaxial. Si l'on utilise une alimentation par coaxial (50 Ohms, comme c'est souvent le cas), on en profite pour ajouter un balun de rapport 1:4 afin de pouvoir l'attaquer en basse impédance.
En pratique, cette antenne couvre les bandes de 3 à 30 MHz.
La résistance de charge doit pouvoir dissiper 1/3 de la puissance d'émission. Elle doit être non inductive. L'impédance de cette antenne est de 600 Ohms. Pratiquement, on peut la faire fonctionner à 50 Ohms, mais son comportement sera alors nettement moins bon. Dans la réalité, on se limitera à 300 Ohms pour la valeur la plus basse. La résistance de charge sera légèrement supérieure à l'impédance de la ligne d'alimentation .
[
Web Creator]
[
LMSOFT]